Note
For detailed information about the Procedure for
BIS ISI Certification, visit:
Our Products
It is challenging to survive in this cutthroat market without a product of standardized quality and certification. To gain market reliance on their products, industries must produce a standard quality product.
INTRODUCTION
It is challenging to survive in this cutthroat market without a product of standardized quality and certification. To gain market reliance on their products, industries must produce a standard quality product.
The manufacturer must make sure that their product complies with the Indian standard in order to receive BIS certification and produce a high-quality product. BIS license might also be necessary to use the standard ISI Mark and sell products in India.
Let's take a closer look at IS 1269 (Part 1): 1997 for Woven Metallic and Glass Fibre Tape Measures of Length.
This standard specifies the requirements for woven metallic and glass fibre tape measures intended for use where rigid length measurements are not possible. It does not apply to high-precision tapes used in the field of mechanics or geodesy by industry (for example gauge blocks, geodetic wire, precision scales).
As per IS 1269 (Part 1): 1997, Woven Metallic and Glass Fibre Tape Measures of Length are classified as follows:
| Nominal Length | Accuracy Class |
|---|---|
| 0.5 m to 5 m | Class II or Class III |
| Above 5m to 100m | Class I, Class II or Class III |
Under normal conditions of use, the materials used must be adequate, strong, stable, and resistant to atmospheric conditions, and they must meet the requirements specified in the standard. The tape major could be made of a suitable fabric or plastic. Tape measures must be well-made, sturdy, and meticulously finished. Clear, regular, and indelible graduated scales are required. The tape must comply with the requirements of the applicable Indian standard. It is necessary to keep an adequately staffed and resourced laboratory in order to carry out the various tests outlined in the standard.
TESTS
The following test shall be carried out as per method specified in the standard.
- Bend Test
- Permanent Set Test
- Sticking Test
- Water Proofing Test
- Nominal Length
- Accuracy class
- Construction
- Graduations
- Coating stability test
Marking
Labelling and marking must be done in accordance with IS 1269 (Part 1) 1997. All products that meet the Indian Standard and are covered by the licence must bear the standard ISI mark. A BIS license for Woven Metallic and Glass Fibre Tape Measures of Length is granted to use the standard mark as per IS 1269 (Part 1) 1997.
To use a standard mark, the manufacturer must first obtain a BIS license for Woven Metallic and Glass Fibre Tape Measures from the Bureau of Indian Standards. The Bureau grants a BIS licence based on a successful assessment of the manufacturing infrastructure, quality control and testing capabilities, and manufacturing process. To ensure that the product meets the requirements of applicable Indian standards, BIS certification for Woven Metallic and Glass Fibre Tape Measures of Lengthis required. BIS certification helps manufacturers gain consumer trust and continue to export and sell their products in the Indian market.
Process
Process for BIS ISI Mark Certification
A streamlined process designed to ensure compliance, quality, and efficiency at every step.
01
Documentation
Preparation and submission of required documents.
02
Application Submission
Filing the application with BIS along with applicable fees.
03
BIS Audit
Inspection and evaluation of manufacturing facility.
04
Sample Testing
Testing of product samples in BIS recognized laboratory.
05
Grant of License
Successful evaluation and grant of BIS ISI Mark license.
Learn the complete process
Watch our detailed video to understand each step involved in obtaining BIS ISI Mark Certification.
Timeline for BIS Certification
The estimated time frame for obtaining BIS certification under IS 1269 (PART 1) is:
For Indian Manufacturers
(Standard Timeframe)30 Days
For Foreign Manufacturers
(Standard Timeframe)180 Days
Conclusion
If a product falls under the scope of the BIS Conformity Assessment Scheme, All the manufacturers, importers, and foreign entities must obtain BIS ISI Certification. The Bureau may cancel the License if the product fails to meet certification requirements.
Aleph INDIA has been serving the industry as a single-window operator for all product regulatory compliance. We can assist importers or manufacturers in meeting all criteria for importing or selling a product in the Indian market.
Partner with Aleph INDIA to simplify your BIS certification journey and ensure full compliance with IS 1269 (PART 1) for robust and high-performance packaging solutions.
RECENT INTERNATIONAL AUDITS
View All Audits
Building Trust. Ensuring Compliance.
Italy Mr. Tiwari is assisting Mr. Anuj Bhatnagar (Head of Laboratory & Policy Planning Department and Head of Northern regional labs) during the audit conducted fo...
Indonesia Another Successful Audit completed by the Bureau of Indian Standards! Proud moment as Aleph INDIA Group's client, M/S. PT. Permata Hijau Palm Oleo, Indonesia...
South Korea As the distinguished national certification authority of India, the Bureau of Indian Standards successfully conducted a BIS Audit for M/s Lotte Chemical Corp...
Testimonials
Hear from industry leaders who have experienced the
impact of partnering with
Aleph.
Aleph INDIA
Mr. Abhijeet Chitlange
Sr. Sales Manager
IVicon Security Tech Private Ltd
Aleph INDIA
Mrs. Chaithra YS
Project Manager | Remidio
Innovation Solutions Pvt Ltd
Aleph INDIA
Mr. Anand Ramaswami
CEO | Makercubs
Technologies Pvt Ltd
Aleph INDIA
Mr. CHANDRA KUMAR N R
Technical Vice President |
AIR LIQUIDE MEDICAL SYSTEMS PRIVATE LIMITED
