Note
For detailed information about the Procedure for
BIS ISI Certification, visit:
Our Products
When we are a manufacturer, we always want to increase our market share and brand values. In this competitive scenario, it isn't easy to survive in the market without a standard quality and certified product. BIS license may also be required to sell product in Indian market.
To get BIS certification and produce a standard quality product, ensure that your product must follow the specified Indian Standard for that product.
Let's take a closer look at IS 7834 (Parts 1 to 8):1987 for Injection Moulded PVC Socket Fittings with Solvent Cement Joints for Water Supplies.
IS 7834 (Part 1) General requirement: This standard (Part 1) specifies the general requirements for the materials, manufacture, test methods, inspection, and marking of all types of injection moulded PVC socket fittings intended for connection, by using solvent cement, to PVC pipes covered by IS: 4985-1988 for water supply.
IS 7834 (Parts 18): 1987 specifies the requirements for various types of injection moulded PVC socket fittings with solvent cement joints for water supply systems, as detailed below:
- Part 1 General requirements
- Part 2 Specific requirements for 45 degrees elbows
- Part 3 Specific requirements for 90-degree elbows
- Part 4 Specific requirements for 90-degree tees
- Part 5 Specific Requirements for 45-degree tees
- Part 6 Specific requirements for sockets
- Part 7 Specific requirements for unions
- Part 8 Specific requirements for caps
Each type of fittings is categorized into the following groups based on size:
TESTS
| Type of fittings | Group 1 | Group 2 | Group 3 |
|---|---|---|---|
| 45 degrees elbow | 16-63 mm | 75-160 mm | 180-315 mm |
| 90 degrees elbow | 16-63 mm | 75-160 mm | 180-315 mm |
| 90 degrees tees | 16-63 mm | 75-160 mm | 180-315 mm |
| 45 degrees tees | 16-63 mm | 75-160 mm | - |
| sockets | 16-63 mm | 75-160 mm | 180-315 mm |
| unions | 16-63 mm | - | - |
| caps | 16-63 mm | 75-160 mm | 180-315 mm |
The material from which the fitting is made must be primarily composed of polyvinyl chloride, to which only those additives necessary to facilitate the manufacture of sound pipe with a good surface finish, mechanical strength, and opacity may be added.
The fitting shall be subjected to the following test:
- Test required
- Stress relief test
- Opacity test
- Effect on water
- Short term hydraulic test
- Dimension test
- Type test
- Acceptance test
All fittings must be clearly and indelibly marked at a prominent location with the Manufacturer's identification mark, the size of the fitting, and the appropriate class to which the fitting's pressure rating corresponds. The product must be labelled in accordance with the applicable part. The Firm must declare the types of fittings, pressure classes, and sizes they intend to cover in the License.
The Standard Mark (ISI Mark) may also be applied to each fittings. The Manufacturer must obtain a BIS license from the Bureau of Indian Standards to use a standard mark (ISI Mark). The Bureau grants a license based on a successful assessment of manufacturing infrastructure, production process, and quality control and testing capabilities during a visit to its manufacturing premises.
Process
Process for BIS ISI Mark Certification
A streamlined process designed to ensure compliance, quality, and efficiency at every step.
01
Documentation
Preparation and submission of required documents.
02
Application Submission
Filing the application with BIS along with applicable fees.
03
BIS Audit
Inspection and evaluation of manufacturing facility.
04
Sample Testing
Testing of product samples in BIS recognized laboratory.
05
Grant of License
Successful evaluation and grant of BIS ISI Mark license.
Learn the complete process
Watch our detailed video to understand each step involved in obtaining BIS ISI Mark Certification.
Timeline for BIS Certification
The estimated time frame for obtaining BIS certification under IS 7834(PARTS 1 TO 8) is:
For Indian Manufacturers
(Standard Timeframe)30 Days
For Foreign Manufacturers
(Standard Timeframe)180 Days
Conclusion
If a product falls under the scope of the BIS Conformity Assessment Scheme, All the manufacturers, importers, and foreign entities must obtain BIS ISI Certification. The Bureau may cancel the License if the product fails to meet certification requirements.
Aleph INDIA has been serving the industry as a single-window operator for all product regulatory compliance. We can assist importers or manufacturers in meeting all criteria for importing or selling a product in the Indian market.
Partner with Aleph INDIA to simplify your BIS certification journey and ensure full compliance with IS 7834(PARTS 1 TO 8) for robust and high-performance packaging solutions.
RECENT INTERNATIONAL AUDITS
View All Audits
Building Trust. Ensuring Compliance.
China Here Mr Yogesh K.T. having brunch with Mr. Sandeep Kumar (Scientist C: CRS Department - Bureau of Indian Standards) and other members of the team during the ...
Indonesia The Bureau of Indian Standards, has finished the BIS Audit for M/S Pt. Ineos Aromatics in Indonesia. Terephthalic acid was the specific focus of this extensi...
Malaysia We are thrilled to share that Aleph INDIA participated in another audit conducted by Indian regulatory compliance authority Bureau of Indian Standards (BIS) ...
Testimonials
Hear from industry leaders who have experienced the
impact of partnering with
Aleph.
Aleph INDIA
Mr. Abhijeet Chitlange
Sr. Sales Manager
IVicon Security Tech Private Ltd
Aleph INDIA
Mrs. Chaithra YS
Project Manager | Remidio
Innovation Solutions Pvt Ltd
Aleph INDIA
Mr. Anand Ramaswami
CEO | Makercubs
Technologies Pvt Ltd
Aleph INDIA
Mr. CHANDRA KUMAR N R
Technical Vice President |
AIR LIQUIDE MEDICAL SYSTEMS PRIVATE LIMITED
